Heat-controller Water Source Heat Pump User Manual Page 54
- Page / 126
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
- WHP - Water Source Heat Pump 1
- Design, Installation & 1
- Operations Manual 1
- WattMaster WHP 3
- Section 1 5
- Conventions 7
- General Information 8
- WattMaster WHP Control System 10
- Make Up Air Controller 11
- WHP Sequence of 12
- Operation 12
- Occupied/Unoccupied Mode of 13
- Vent Mode Operation 13
- Off Mode of Operation 13
- WHP Loop Controller 16
- Sequence of Operations 16
- Pump VFD Control 17
- Compressor Control 17
- Heat Rejection Control 18
- Heat Addition Control 18
- Staged Heat Addition 19
- Proportional Heat Addition 19
- Water Temperature Alarming 20
- Fire Alarm 20
- System Manager 21
- Typical WHP Controller Wiring 21
- Section 1 WattMaster WHP 22
- 1-16 Design Guide 22
- Section 2 23
- Tips Before Beginning 25
- Installation 25
- System Overview 26
- Communications Loops 27
- TO OTHER MINILINKS 28
- (NETWORK TERMINALS ONLY) 28
- TO OTHER WHP CONTROLLERS 28
- WattMaster WHP Section 2 31
- Installation and Wiring 2-7 31
- Duct Sensor with Thermowell 34
- Outside Air Temperature 36
- CommLink II Interface 37
- WHP Controller 38
- CAUTION! 39
- Addressing 41
- MiniLink Addressing 42
- Room Sensors 43
- Room Sensor 44
- Supply Air Temperature 45
- Leaving Water 46
- Temperature Sensors 46
- Section 3 47
- LCD/Keypad Operations 49
- System Manager Layout 50
- Keypad Functions 50
- System Manager LED Indicators 51
- Heat Pump Status 52
- Status Screen #1 53
- Status Screen #2 53
- Status Screen #3 54
- Status Screen #4 54
- Status Screen #5 54
- Status Screen #6 55
- View Alarms 56
- Set Time & Date 57
- Programming Date 58
- Daylight Savings Adjustments 58
- New Passcodes 59
- Rebuild Alarm Map 60
- Heat Pump Setpoints 61
- Setpoint Screen #2 62
- Setpoint Screen #3 62
- Setpoint Screen #4 62
- Setpoint Screen #5 63
- Setpoint Screen #6 63
- Setpoint Screen #7 63
- Setpoint Screen #8 64
- Setpoint Screen #9 64
- Setpoint Screen #10 64
- Setpoint Screen #11 65
- Setpoint Screen #12 65
- Setpoint Screen #13 65
- Setpoint Screen #14 66
- Setpoint Screen #15 66
- Setpoint Screen #16 66
- Setpoint Screen #17 67
- Setpoint Screen #18 67
- Setpoint Screen #19 67
- 2) WHP Schedules 68
- Holidays 69
- 3) Reset Pumps 70
- Loop Controller Status 71
- Status Screen #3 72
- Status Screen #4 72
- Status Screen #7 74
- Status Screen #8 74
- Loop Controller Setpoints 75
- Setpoint Screens #13 79
- Section 3 WattMaster WHP 80
- 3-32 Programming 80
- Section 4 81
- 1.0 Communications 83
- Overview 83
- Communications Loop Routing 85
- 2.0 WHP Controller 86
- Controller 87
- 2.2.2 Analog Inputs 88
- 2.2.6 WHP Controller Wiring 90
- 3.0 Loop Controller 91
- 3.2.1 Analog Inputs 92
- 3.2.2 Analog Output 92
- 3.2.3 Binary Output 93
- 3.2.7 Power Terminal 94
- 4.0 Start-Up 96
- 4.3 Communications Checklist 97
- Information 98
- Communications Loop Wiring 100
- 4.5 Setting Address Switches 101
- WattMaster WHP Section 4 102
- 5.0 Troubleshooting 103
- 5.2 Alarms 105
- 5.3.7 (continued) 113
- Diagram Overvie 117
- Measurements 117
- 5.4.1 (continued) 118
- Caution: AIN1 – Fire/Smoke 118
- Comm Driver Chip Replacement 122
- E-mail: [email protected] 126
© 2020, manymanuals.com. All rights reserved. | 0.955 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals